Difference between revisions of "48-pin Module Family"
Line 1: | Line 1: | ||
[[Image:ECM048.jpg|200px]] | [[Image:ECM048.jpg|200px]] | ||
+ | |||
+ | See [http://www.woodward.com/publicationsdownload.aspx?DocumentNumber=36300 Product Guide] for Detailed Part Numbers of Modules and Related Part Numbers (Harnesses, Connectors..) as well as Block Diagram IO comparisons. | ||
==ECM-0563-048== | ==ECM-0563-048== |
Revision as of 10:22, 27 September 2012
See Product Guide for Detailed Part Numbers of Modules and Related Part Numbers (Harnesses, Connectors..) as well as Block Diagram IO comparisons.
Contents
ECM-0563-048
Hardware Features
- Microprocessor: MPC563, 56MHz
- Memory: 512K Flash, 32K RAM(24K+4K overlayable)
- 128K parallel EEPROM (ECM-0563-048-0701-C)
- Operating Voltage: 8-16VDC
- Operating Temperature: -40° to 105° C
- Sealed Connectors Operable to 10ft submerged
Inputs
- 13 Analog Inputs
- 2 VR/HallFrequency Inputs
Outputs
- 4 Low Side Injector Drivers
- 8 TTL Level Ignition System Outputs
- 5 High Current Low Side PWMs
- 2 5A H-Bridge PWMs with Current Feedback
- Independent Transducer Power Supply
- 1 Low SideRelay Driver (Main Power)
Datalinks
- 1 CAN 2.0B Channel
Notes GHS 3.6 or 4.2.1 version required, GCC may be used also.
Differences:
ECM-0563-048-0701: 1 CAN channel, 13 analog inputs, 2 digital/VR inputs, 4 injector/low-side drivers, 8 TTL spark timing outputs, 5 low-side drivers, 2 H-bridges, one Main Power Relay low-side driver.
ECM-0563-048-0705: similar to ECM-0563-048-0701 module, including same pull-up / pull-down resistors, but only has 1 H-bridge and has 2 more low-side drivers.
ECM-0563-048-0806: same as ECM-0563-048-0705 module, but with different hardboot code
ECM-0563-048-0704: same features as ECM-0563-048-0705, but pull-up / pull-down resistors are different.
GCM-0563-048 General Control Module
Hardware Features
- Microprocessor: MPC563, 40MHz
- Memory: 512K Flash, 32K RAM (4K overlayable)
- 16K serial EEPROM
- 128K parallel EEPROM (GCM-0563-048-0801-C)
- Operating Voltage: 8-32VDC
- Operating Temperature: -40° to 105° C
- Sealed Connectors Operable to 10ft. submerged
Inputs
- Up to 16 Analog Inputs
- Up to 7 Discrete/Frequency Inputs
- Up to 2 VR/Hall Frequency Inputs
- 1 Emergency Stop Input
Outputs
- 2 3A Low Side Drivers w/Current Feedback
- 4 3A Low Side Drivers
- 2 2.9A High Side Drivers
- 1 1A EasyLink/Low Side Driver
- 1 Relay Driver (Main Power)
- 1 10A H-Bridge Driver
Datalinks
- 3 CAN 2.0B Channels
HCM-0563-048 Hydraulic Control Module
Hardware Features
- Microprocessor: MPC563, 40MHz
- Memory: 512K Flash, 32K RAM (4K overlayable)
- 16K serial EEPROM
- 128K parallel EEPROM
- Operating Voltage: 8-32VDC
- Operating Temperature: -40° to 85° C
- Sealed Connectors Operable to 10ft. submerged
Inputs
- Up to 16 Analog Inputs
- Up to 6 Discrete/Frequency Inputs
- Up to 2 VR/Hall Frequency Inputs
- 1 Knock/Drive Noise Detector Input
- 1 Stop Input
Outputs
- 6 2.5A Low Side Drivers w/Current Feedback
- 4 3A Low Side Drivers
- 1 1A EasyLink/Low Side Driver
- 1 Relay Driver (Main Power)
Datalinks
- 2 CAN 2.0B Channels
ECM-0555-048
Hardware Features
- Microprocessor: Freescale MPC555, 40MHz
- Memory: 448K Flash, 26K RAM,
- 4K serial EEPROM Flash, Except: 0710 - 8K serial EEPROM
- Calibratible Memory: 64K parallel EEPROM
- Operating Voltage: 8-16VDC
- Operating Temperature: -40° to 85° C (in benchmark marine engine application)
- Sealed Connectors Operable to 10 ft. submerged
Inputs*
- 12 to 15 Analog Inputs
- 3 or 4 Low Frequency Digital Inputs
- 1 or 2 Hall Effect Frequency Inputs (cam)
- 0 or 1 Variable Reluctance Frequency Input (crank)
- 0 to 2 Knock Sensor Inputs
- 1 Stop Input
Outputs*
- 4 Injector Driver Outputs
- 1 to 4 Electronic Spark Trigger (5V) Ouputs
- 1 Tachometer Output
- 4 or 5 Low Side Outputs
- 1 Main Power Relay Driver Output
Datalinks
- 1 CAN 2.0B Channel
- 1 RS-485 Channel