Difference between revisions of "48-pin Module Family"
(→ECM Differences:) |
(→Part Numbers) |
||
Line 84: | Line 84: | ||
[[Image: GCM48_pn.png]] | [[Image: GCM48_pn.png]] | ||
+ | == Frequently Asked Questions == | ||
+ | Can I use voltages over 5V on the analog channels? Using voltage over 5V is not recommended on analogs with Pull Up resistors. The analogs with 220k PD can handle 24V input. | ||
==HCM-0563-048 Hydraulic Control Module == | ==HCM-0563-048 Hydraulic Control Module == |
Revision as of 08:21, 4 November 2013
See Product Guide for Detailed Part Numbers of Modules and Related Part Numbers (Harnesses, Connectors..) as well as Block Diagram IO comparisons.
Contents
ECM-0563-048
Hardware Features
- Microprocessor: MPC563, 56MHz
- Memory: 512K Flash*, 32K RAM(24K+4K overlayable)
- 128K parallel EEPROM (ECM-0563-048-0701-C)
- Operating Voltage: 8-16VDC
- Operating Temperature: -40° to 105° C
- Sealed Connectors Operable to 10ft submerged
Note: DEV vs PROD Flash Memory The 48-pin modules have 512k Flash memory, but not all of that is available for general use. 64k of this memory is reserved for Module Configuration and Hardboot and cannot be used by the application. The PROD module will also have an additional 64k less memory because 64k of flash is reserved for calibration space. The calibrations for the DEV module are stored in a parallel EEPROM, so the 64k of flash is not reserved.
Inputs
- 13 Analog Inputs
- 2 VR/HallFrequency Inputs
Outputs
- 4 Low Side Injector Drivers
- 8 TTL Level Ignition System Outputs
- 5 High Current Low Side PWMs
- 2 5A H-Bridge PWMs with Current Feedback
- Independent Transducer Power Supply
- 1 Low SideRelay Driver (Main Power)
Datalinks
- 1 CAN 2.0B Channel
Notes GHS 3.6, 4.2.1, or 4.2.4 version required, GCC may be used also.
Part Numbers
ECM Differences:
ECM-0563-048-0701: 1 CAN channel, 13 analog inputs, 2 digital/VR inputs, 4 injector/low-side drivers, 8 TTL spark timing outputs, 5 low-side drivers, 2 H-bridges, one Main Power Relay low-side driver.
ECM-0563-048-0705: similar to ECM-0563-048-0701 module, including same pull-up / pull-down resistors, but only has 1 H-bridge and has 2 more low-side drivers.
ECM-0563-048-0806: same as ECM-0563-048-0705 module, but with different boot code
ECM-0563-048-0704: same features as ECM-0563-048-0705, but pull-up / pull-down resistors are different.
FAQ
I have a model that builds on the DEV module, but on the PROD the build fails with an out of flash memory link error: (error) section .romcals (0x6ff8c-0x70e3b) doesn't fit in memory block FLASH (0x10100-0x6ffff). The PROD module has effectively 64k less general purpose flash than the DEV module because a fixed 64k is reserved to store calibrations on the PROD module. The DEV module stores these calibrations in parallel EEPROM so this space is not reserved.
I am getting the out of memory build error described above, but the build statistics show that there is flash available There is an error in the build stats where the 64k reserved for calibration is counted twice. This is a known issue, and will be fixed in a future release.
GCM-0563-048 General Control Module
Hardware Features
- Microprocessor: MPC563, 40MHz
- Memory: 512K Flash, 32K RAM (4K overlayable)
- 16K serial EEPROM
- 128K parallel EEPROM (GCM-0563-048-0801-C)
- Operating Voltage: 8-32VDC
- Operating Temperature: -40° to 105° C
- Sealed Connectors Operable to 10ft. submerged
Inputs
- Up to 16 Analog Inputs
- Up to 7 Discrete/Frequency Inputs
- Up to 2 VR/Hall Frequency Inputs
- 1 Emergency Stop Input
Outputs
- 2 3A Low Side Drivers w/Current Feedback
- 4 3A Low Side Drivers
- 2 2.9A High Side Drivers
- 1 1A EasyLink/Low Side Driver
- 1 Relay Driver (Main Power)
- 1 10A H-Bridge Driver
Datalinks
- 3 CAN 2.0B Channels
Part Numbers
Frequently Asked Questions
Can I use voltages over 5V on the analog channels? Using voltage over 5V is not recommended on analogs with Pull Up resistors. The analogs with 220k PD can handle 24V input.
HCM-0563-048 Hydraulic Control Module
Hardware Features
- Microprocessor: MPC563, 40MHz
- Memory: 512K Flash, 32K RAM (4K overlayable)
- 16K serial EEPROM
- 128K parallel EEPROM
- Operating Voltage: 8-32VDC
- Operating Temperature: -40° to 85° C
- Sealed Connectors Operable to 10ft. submerged
Inputs
- Up to 16 Analog Inputs
- Up to 6 Discrete/Frequency Inputs
- Up to 2 VR/Hall Frequency Inputs
- 1 Knock/Drive Noise Detector Input
- 1 Stop Input
Outputs
- 6 2.5A Low Side Drivers w/Current Feedback
- 4 3A Low Side Drivers
- 1 1A EasyLink/Low Side Driver
- 1 Relay Driver (Main Power)
Datalinks
- 2 CAN 2.0B Channels
Part Numbers
ECM-0555-048
Hardware Features
- Microprocessor: Freescale MPC555, 40MHz
- Memory: 448K Flash, 26K RAM,
- 4K serial EEPROM Flash, Except: 0710 - 8K serial EEPROM
- Calibratible Memory: 64K parallel EEPROM
- Operating Voltage: 8-16VDC
- Operating Temperature: -40° to 85° C (in benchmark marine engine application)
- Sealed Connectors Operable to 10 ft. submerged
Inputs
- 12 to 15 Analog Inputs
- 3 or 4 Low Frequency Digital Inputs
- 1 or 2 Hall Effect Frequency Inputs (cam)
- 0 or 1 Variable Reluctance Frequency Input (crank)
- 0 to 2 Knock Sensor Inputs
- 1 Stop Input
Outputs*
- 4 Injector Driver Outputs
- 1 to 4 Electronic Spark Trigger (5V) Ouputs
- 1 Tachometer Output
- 4 or 5 Low Side Outputs
- 1 Main Power Relay Driver Output
Datalinks
- 1 CAN 2.0B Channel
- 1 RS-485 Channel