48-pin Module Family

See Product Guide for Detailed Part Numbers of Modules and Related Part Numbers (Harnesses, Connectors..) as well as Block Diagram IO comparisons.

ECM-0563-048

Hardware Features

Microprocessor: MPC563, 56MHz

Memory: 512K Flash*, 32K RAM(24K+4K overlayable)

128K parallel EEPROM (ECM-0563-048-0701-C)

Operating Voltage: 8-16VDC

Operating Temperature: -40° to 105° C

Sealed Connectors Operable to 10ft submerged

Note: DEV vs PROD Flash Memory The 48-pin modules have 512k Flash memory, but not all of that is available for general use. 64k of this memory is reserved for Module Configuration and Hardboot and cannot be used by the application. The PROD module will also have an additional 64k less memory because 64k of flash is reserved for calibration space. The calibrations for the DEV module are stored in a parallel EEPROM, so the 64k of flash is not reserved.

Inputs

• 13 Analog Inputs
• 2 VR/HallFrequency Inputs

Outputs

4 Low Side Injector Drivers

8 TTL Level Ignition System Outputs

5 High Current Low Side PWMs

2 5A H-Bridge PWMs with Current Feedback

Independent Transducer Power Supply

1 Low SideRelay Driver (Main Power)

Datalinks

• 1 CAN 2.0B Channel

Notes GHS 3.6, 4.2.1, or 4.2.4 version required, GCC may be used also.

Part Numbers

ECM Differences:

ECM-0563-048-0701: 1 CAN channel, 13 analog inputs, 2 digital/VR inputs, 4 injector/low-side drivers, 8 TTL spark timing outputs, 5 low-side drivers, 2 H-bridges, one Main Power Relay low-side driver.

ECM-0563-048-0705: similar to ECM-0563-048-0701 module, including same pull-up / pull-down resistors, but only has 1 H-bridge and has 2 more low-side drivers.

ECM-0563-048-0806: same as ECM-0563-048-0705 module, but with different boot code

ECM-0563-048-0704: same features as ECM-0563-048-0705, but pull-up / pull-down resistors are different.

FAQ

I have a model that builds on the DEV module, but on the PROD the build fails with an out of flash memory link error: (error) section .romcals (0x6ff8c-0x70e3b) doesn't fit in memory block FLASH (0x10100-0x6ffff). The PROD module has effectively 64k less general purpose flash than the DEV module because a fixed 64k is reserved to store calibrations on the PROD module. The DEV module stores these calibrations in parallel EEPROM so this space is not reserved.

I am getting the out of memory build error described above, but the build statistics show that there is flash available There is an error in the build stats where the 64k reserved for calibration is counted twice. This is a known issue, and will be fixed in a future release.

GCM-0563-048 General Control Module

Hardware Features

Microprocessor: MPC563, 40MHz

Memory: 512K Flash, 32K RAM (4K overlayable)

16K serial EEPROM

128K parallel EEPROM (GCM-0563-048-0801-C)

Operating Voltage: 8-32VDC

Operating Temperature: -40° to 105° C

Sealed Connectors Operable to 10ft. submerged

Inputs

Up to 16 Analog Inputs

Up to 7 Discrete/Frequency Inputs

Up to 2 VR/Hall Frequency Inputs

1 Emergency Stop Input

Outputs

2 3A Low Side Drivers w/Current Feedback

4 3A Low Side Drivers

2 2.9A High Side Drivers

1 1A EasyLink/Low Side Driver

1 Relay Driver (Main Power)

1 10A H-Bridge Driver

Datalinks

3 CAN 2.0B Channels

• • CAN-1 must be used for programming

Part Numbers

Part number 1751-6332 is also GCM05630480804F00.
Part number 1751-6509 is also GCM05630480804CP0.

Part number 1751-6692 supersedes 1751-6332 as GCM05630480806F00.

Part number 1751-6326 is also GCM05630480803F00.
Part number 1751-6508 is also GCM05630480803CP0.

Frequently Asked Questions

Can I use voltages over 5V on the analog channels? Using voltage over 5V is not recommended on analogs with Pull Up resistors. The analogs with 220k PD can handle 24V input.

HCM-0563-048 Hydraulic Control Module

Hardware Features

Microprocessor: MPC563, 40MHz

Memory: 512K Flash, 32K RAM (4K overlayable)

16K serial EEPROM

128K parallel EEPROM

Operating Voltage: 8-32VDC

Operating Temperature: -40° to 85° C

Sealed Connectors Operable to 10ft. submerged

Inputs

Up to 16 Analog Inputs

Up to 6 Discrete/Frequency Inputs

Up to 2 VR/Hall Frequency Inputs

1 Knock/Drive Noise Detector Input

1 Stop Input

Outputs

6 2.5A Low Side Drivers w/Current Feedback

4 3A Low Side Drivers

1 1A EasyLink/Low Side Driver

1 Relay Driver (Main Power)

Datalinks

2 CAN 2.0B Channels

• • CAN-1 must be used for programming

Part Numbers

ECM-0555-048

Hardware Features

Microprocessor: Freescale MPC555, 40MHz

Memory: 448K Flash, 26K RAM,

4K serial EEPROM Flash, Except: 0710 - 8K serial EEPROM

Calibratible Memory: 64K parallel EEPROM

Operating Voltage: 8-16VDC

Operating Temperature: -40° to 85° C (in benchmark marine engine application)

Sealed Connectors Operable to 10 ft. submerged

Inputs

12 to 15 Analog Inputs

3 or 4 Low Frequency Digital Inputs

1 or 2 Hall Effect Frequency Inputs (cam)

0 or 1 Variable Reluctance Frequency Input (crank)

0 to 2 Knock Sensor Inputs

1 Stop Input

Outputs*

4 Injector Driver Outputs

1 to 4 Electronic Spark Trigger (5V) Ouputs

1 Tachometer Output

4 or 5 Low Side Outputs

1 Main Power Relay Driver Output

Datalinks

1 CAN 2.0B Channel

1 RS-485 Channel

Part Numbers